Discussion:
Report Head cuts off
(too old to reply)
Alvaro Nunes
2004-10-04 13:01:44 UTC
Permalink
Hi,

Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.

It seems SP2 is giving me hardtime. I will de-install it.

Alvaro
Alvaro Nunes
2004-10-04 13:12:50 UTC
Permalink
I have to add, that I tested printing an older version of that Report,
that was working before and happens the same.
Alvaro
Post by Alvaro Nunes
Hi,
Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.
It seems SP2 is giving me hardtime. I will de-install it.
Alvaro
Jeff Shoaf
2004-10-04 13:42:08 UTC
Permalink
Are you printing to the same printer with each version? Some printers
have larger margin requirements...
Post by Alvaro Nunes
I have to add, that I tested printing an older version of that Report,
that was working before and happens the same.
Alvaro
Post by Alvaro Nunes
Hi,
Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.
It seems SP2 is giving me hardtime. I will de-install it.
Alvaro
Alvaro Nunes
2004-10-04 14:17:52 UTC
Permalink
Jeff,
Yes I am printing to same printer.
It seems to be that under SP2 the report is not beeing resized correctly.
The min margin for printer is 3 mm(Handbook) and I setup page to 1.6mm.
But it was working fine before. Now with SP2 it just cuts off and
beyhond the min margin, more 5mm than necessary.
Alvaro
Post by Jeff Shoaf
Are you printing to the same printer with each version? Some printers
have larger margin requirements...
Post by Alvaro Nunes
I have to add, that I tested printing an older version of that Report,
that was working before and happens the same.
Alvaro
Post by Alvaro Nunes
Hi,
Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.
It seems SP2 is giving me hardtime. I will de-install it.
Alvaro
Jeff Shoaf
2004-10-04 15:21:42 UTC
Permalink
One of the P9 SP's has problems with metric paper sizes, but I don't
remember which one - maybe Bertil will step in.
Post by Alvaro Nunes
Jeff,
Yes I am printing to same printer.
It seems to be that under SP2 the report is not beeing resized correctly.
The min margin for printer is 3 mm(Handbook) and I setup page to 1.6mm.
But it was working fine before. Now with SP2 it just cuts off and
beyhond the min margin, more 5mm than necessary.
Alvaro
Post by Jeff Shoaf
Are you printing to the same printer with each version? Some printers
have larger margin requirements...
Post by Alvaro Nunes
I have to add, that I tested printing an older version of that
Report, that was working before and happens the same.
Alvaro
Post by Alvaro Nunes
Hi,
Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.
It seems SP2 is giving me hardtime. I will de-install it.
Alvaro
Bertil Isberg
2004-10-04 20:05:19 UTC
Permalink
Jeff

<<
One of the P9 SP's has problems with metric paper sizes
Alvaro is using P10.


I found another one - P9 specific- in my files, that looks more like
Alvaro's problem
Paradox 9:
After installing SP2, the phenomenon where reports printed on an HP 6P were
offset down and to the right one quarter of an inch has returned, EXCEPT
that while previously it only occurred when printing reports interactively,
now it also occurs when printing with ObjectPal.

The offset is equal to the unprintable area set in Win98. In my case .083"
top and .25" left. If you change the setting in Windows, the text in the
report will move accordingly, ie setting unprintable area top and bottom to
0" puts the text in the proper position. But this does not affect lines,
boxes and frames. They remain offset improperly.

Reported by: Greg Milakovich <greg_milakovichATcsi.com>
26 December 1999 03:38
--
Bertil Isberg - CTECH
Paradox buglist:
online: http://w1.826.comhem.se/~u82608896/
FAQ newsgroup: corel.wpoffice.paradox-faq
Alvaro Nunes
2004-10-31 16:12:48 UTC
Permalink
OK, I uninstalled SP2_XP now and this problem is gone.
Alvaro
Post by Alvaro Nunes
Hi,
Printing a Report with PDox 10 , it cutts off about 8 mm of top of report.
Printing that report in Pdox Runtine it prints normally!
Report pageSize is A5 Rotated. Margins set to minimum = 1.6 mm.
Machine for Pdox full is WinXPSP2 and for Runtime without SP2.
It seems SP2 is giving me hardtime. I will de-install it.
Alvaro
Loading...